Electric ceramic kilns: a complete buying guide

Request information

Choosing among the electric ceramic kilns on the market means weighing up a few key parameters: the type of material to be fired, the number of pieces, the space available and the electrical supply. This guide summarises the main criteria, both for people who work with ceramics as a hobby and for studios, schools and small craft businesses.

1. Maximum temperature: low or high fire

The first criterion is the material. Ceramic kilns fall into two broad families:

  • low-temperature kilns, up to about 1100 °C, suitable for terracotta, majolica, low-fire glazes, third firing, decals, photo ceramics and small glass work;
  • high-temperature kilns, up to 1260–1300 °C, needed for stoneware and porcelain.

A high-temperature kiln can also carry out every low-temperature firing, but not the other way round. If you think you may move on to stoneware in the future, it is worth considering a high-temperature model from the start. The temperature ranges of the different firings are covered in the article on ceramic firing temperatures.

In the Faber range the distinction corresponds to two series: FBL kilns reach 1100 °C, FBH kilns reach 1280 °C.

2. Chamber capacity

Capacity is expressed in litres and determines how many pieces can be fired in one cycle. As a rough guide:

  • 40 litres: hobby use, occasional firings, small objects, costume jewellery and decoration;
  • 70–85 litres: hobbyists with regular output, classes, schools and small studios;
  • 100 litres with a tall chamber: vases, sculptures and tall pieces;
  • 150–300 litres: craft studios, art schools and continuous production.

Besides volume, the shape of the chamber matters. A wide base is useful for plates and tiles, while extra height is needed for vases and sculptures. A kiln that is too big for your needs forces you to fire partial loads, with higher consumption per piece; one that is too small means multiplying the number of firings.

3. Power supply

The power of ceramic kilns ranges from about 2.5 kW for 40 litre models up to 8–10 kW for the largest ones. As a general rule:

  • kilns up to about 3 kW run on 230 V single-phase and can be connected to a household supply, with a dedicated circuit and an adequate electricity contract;
  • between 4.5 and 6 kW, either single-phase with a high-capacity supply or three-phase is possible;
  • above 6 kW, 400 V three-phase is generally required.

The topic is covered in detail in the guide to 230 V electric ceramic kilns.

4. Insulation: ceramic fibre or refractory bricks

Insulation affects heating speed, energy consumption and thermal stability. High-density ceramic fibre is light, stores little heat and allows fast ramps with low consumption. Insulating firebrick has a greater thermal mass: it heats up more slowly but holds the temperature very steadily, which is useful in high-temperature firings. The differences are described in the article on fibre or refractory bricks.

5. Firing control

A controller lets you set the firing schedule: ramps, holds and cooling. Things to check are the number of programs that can be stored, the number of segments per program and the safety devices. Faber FBL and FBH kilns use an ATR-621 controller that stores 15 programs of 45 segments, with over-temperature alarm, cycle recovery after a power failure and power cut-off when the door is opened. A practical example is available in the tutorial on programming a firing cycle.

6. Accessories

To make the most of the chamber height you need kiln shelves and props to build up the shelves. A kiln stand raises the kiln to a comfortable height and, if fitted with castors, makes it easier to move.

7. Installation and space

Before buying, check the external dimensions of the kiln, the space needed to open the door and the ventilation of the room. The main recommendations are collected in the guide on where and how to install a ceramic kiln.

8. Support and spare parts

Heating elements and thermocouples are wear parts. Having original spare parts and direct support from the manufacturer makes maintenance easier over the years. Faber, based in Pozzoleone (Vicenza, Italy), has been making electric kilns since 1997 and provides tutorials for the most common replacements, such as the heating elements and the thermocouple.

Summary: which kiln to choose

Need Recommended type Example
First hobby kiln, low-temperature firing 40 litres, 1100 °C, 230 V FBL40
Regular production, classes, schools 70–85 litres, 1100 °C, 230 V FBL70, FBL85
Vases and sculptures 100 litres, 60 cm tall chamber FBL100
Compact stoneware and porcelain kiln 40 litres, 1280 °C, 230 V FBH40
Studio with large loads 150–300 litres FBL150, FBL270, FBL300, FBH150

If you are new to the subject, there is also a dedicated guide to choosing a hobby pottery kiln.

    You may also like

    All articles